Harken 418 Trigger cleat Manuel d'utilisateur télécharger pdf (Page 1)

N15W24983 Bluemound Road • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 701-5780

Web: www.harken.com • Email: [email protected]

OPTIONS: 419 eyestrap; 355 mounting bracket to attach cleat to Harken

Classic blocks: 052, 064, 152, and 411. See reverse side for mounting to

Carbo triple blocks.

Placement

The angle of line from cleat to operator is important for efficient

release. For best operation, mount cleat at waist or chest height

in your normal operating position. If possible, mount cleat on

edge of deck, cockpit, or cabin.

Place mounting holes back 35 mm (1

/8") from edge so cleat overhangs.

Drill size 5 mm (

/64") or #12.

If line angle is too low, or if cleat cannot be mounted near an edge, mount

cleat on pad or bracket inclined 25°. Install bullseye fairlead or turning

block on the loaded side of the cleat to lead line into cleat parallel to cams.

The Trigger cleat will accept most lines up to 12 mm (

").

To adjust cleat to fit larger size line,

loosen screws and lift cam cleat and

its platform slightly from base. Slide

base toward you, against spring

tension. Press cleat and platform

down and hold in place until screws

are tight.

Tip: Mount screws through cleat and deck with nuts loosely threaded.

Screws should be ready to tighten before adjusting for larger line.

Cam base and cam platform have ridges and interlocking grooves

to help hold them in place until screws are tight.

Adjusting Cleat to Fit Line Size

INSTRUCTIONS

Trigger Cleat 418

Strictly follow all instructions to avoid an accident, damage to

your vessel, personal injury, or death. See www.harken.com

for additional safety information.

Part

No.

Max line

Min line

Maximum

working load

Fastener

spacing

Fastener size/

comments

in mm in mm lb kg in mm

5 mm (#10) PH/RH–ships w/1

screws and nuts to hold assembly.

418

12 500 227 2 51

The 418 Trigger cleat allows easy

release of highly-loaded lines with

complete control. Pulling line down

on the trigger mechanism opens

cleat. Line never comes off cleat.

The trigger serves as a snubbing

surface to control release.

Installing 418 Trigger Cleat

35 mm

/8")

Cam gap

With lever fully depressed, cam gap should be

slightly larger than line size. If gap is too small,

shift base to position for larger line size.

With line loaded in cams, lever should not

contact top of lever cavity. This will prevent

cams from closing tightly against line. If rope

slips when loaded, shift base to position for

smaller rope size.

Check for Proper Adjustment

Trigger

1 2

Résumé du contenu

Page 1 - INSTRUCTIONS

N15W24983 Bluemound Road • Pewaukee, WI 53072 U.S.A.Telephone: (262) 691-3320 • Fax: (262) 701-5780Web: www.harken.com • Email: [email protected]

Page 2 - Maintenance

Pull line tail downward as in position B. The release lever opens cams so line may be eased. By holding a downward angle, lever acts as a snubbing sur

Commentaires sur ces manuels

Pas de commentaire

Harken 418 Trigger cleat Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Harken 418 Trigger cleat. Harken 418 Trigger cleat User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Harken 418 Trigger cleat Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Harken 418 Trigger cleat. Harken 418 Trigger cleat User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Harken 418 Trigger cleat